How to Unlock and Recover the Computer using Anvi Rescue Disk?

Anvi Rescue Disk was designed to be used when standard antivirus software fail to detect and clean various computer infections, especially boot-sector viruses like ransomware.
If your computer is severely infected and you are disabled to boot into safe mode, you are highly encouraged to follow the below instruction to recover your computer by using Anvi Rescue Disk with following steps.

Use Anvi Rescue Disk to Unlock and Recover the Computer

step 1

Download the required file.

Download the Anvi Rescue Disk iso image file Rescue.iso and the USB disk production tool BootUsb.exe from Anvisoft official site. (Direct download link)

Please note that Rescue.iso is a large file download; please be patient while it downloads.

step 2

Record Anvi Rescue Disk iso image to USB drive.
You can also record the iso image to a CD/DVD. We will introduce the steps to record iso image to a CD/DVD in following guide.
Connect USB to computer. You’d better backup your important data and format your USB drive before use it to record the iso image.
Locate your download folder and double-clicking on BootUsb.exe to start it. And then click “Choose File” button to browser into your download folder and select Rescue.iso file as your source file.
Select the path of USB drive, such as drive H:
Click “Start Burning” to start the burn of USB Rescue Disk boot drive.
Please close BootUsb.exe tool after you successfully burn the file to USB drive when you get following message.
Now, you have bootable Anvi Rescue Disk to repair your computer.

Alternative Option-Record Anvi Rescue Disk iso image to CD/DVD

You can also record Anvi Rescue Disk iso image to a DV/DVD. Any CD/DVD record software is fine for burn iso image. If you don’t have any, you can download and install Nero Burning ROM and ImgBurn. Here we will use Nero Burning ROM for demonstration purpose.
Please open and start Nero Burning ROM and select Burn Image from the drop-down menu of the Recorder.
Locate your download folder and select Rescue.iso file as your source file and then click Open button.
OK, now, please click Burn button to start record the iso image. After a few minutes, you will have a bootable Anvi Rescue Disk to repair your computer.

step 3

Restart your computer to Anvi Rescue Disk system to kill the virus
Please restart your computer and configure your computer to boot from USB drive/DV/DVD that recorded Anvi Rescue Disk.
Basically, you can use F8 to load USB boot menu.
For different motherboard, you may need to use the Delete or F2, F11 keys, to load the BIOS menu. Normally, the information how to enter the BIOS menu is displayed on the screen at the start of the OS boot.
keys F1, F8, F10, F12 might be used for some motherboards, as well as the following key combinations:

Ctrl+Esc
Ctrl+Ins
Ctrl+Alt
Ctrl+Alt+Esc
Ctrl+Alt+Enter
Ctrl+Alt+Del
Ctrl+Alt+Ins
Ctrl+Alt+S

step 4

Selected the preferred language
After you enter Anvisoft Rescue Disk menu, please selected your preferred language and press Enter to continue.

step 5

Run Anvi Rescue Disk
Now you are in the mini Operating system, please double click Rescue tool to start Anvi Rescue disk.

step 6

Network connection status

Make sure that your computer is connected to network connection before you run a scan on your computer. Please check the tutorial on Network Configuration if you fail to connect your computer to Internet.

step7

Perform Full Scan

Please run a full scan by clicking the “Scan Computer” button in the middle of the program to detect and kill the PC lockup virus.

step 8

Fix problem
Clicking “Fix Now” to Remove the detected threat by Anvi Rescue Disk.

step 9

Repair Registry errors
Switch to Repair tab. Scan and fix the registry error with the “Repair” module of Anvi Rescue Disk.
Important Notice: You must repair the registry error after kill the virus. You are probably disabled to boot your Windows without fixing registry damaged by the virus.

step 10

Restart your computer into normal mode
Now your computer should be clean and unlocked from the virus infection, please restart your computer and boot into normal mode.
Social Share Toolbar
Leave a comment

Comments

10 thoughts on “How to Unlock and Recover the Computer using Anvi Rescue Disk?

  1. ANVI is not for Windows. I burned the iso image. When one boots up it sees the disk and says “Welcome to Grub !” Then on the next line its says. “error: Unknown file System”

    The next line says: “Entering Rescue Mode” then goes to a next line which simple gives a prompt, namely: “Grub Rescue > prompt —- and sits there and blinks. LOL what garbage. And it won’t take a DOS command to show the directory to access the setup.

    I burned a CD for nothing. Hiren’s also uses a Linux system, or so. And its seen in Window Computer. Burning is the simple part, making it bootable which harder was omitted.

    • Hello Dedavid,

      I apologize if there is any problem.

      Anvi Rescue Disk is developed to fix and recover severely infected Windows computer. We can assure you that the tool is for Windows operating system computer.

      To use the tool, you should use a USB drive that more than 512M and use a CD with enough space.

      The reason that your encounter the problem may due to the fact that you are not burning the iso file completely.

      Please try again.

      If any problem, please let us know.

      Thanks a lot for your time.

    • grub is just a boot loader. It would want unix commands, not DOS. If the Cd wasn’t large enough to burn the entire ISO file it will not read right. Try it on a DVD. I haven’t used CD-R in years and don’t remember the size they hold. You can also spend the $8 on a 4gb flash drive

  2. I have followed all the steps and now cannot connect to the network..
    I have wireless network not DSL so that tip won’t help

  3. Won’t connect to the Internet… Have tried everything. Please help!!! Won’t even see a wireless connection and can’t recognize the wired one..

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>